Go Back   Aquarium Advice - Aquarium Forum Community > General Aquarium Forums > General Hardware/Equipment Discussion

Join Aquarium Advice Today
Thread Tools Search this Thread Display Modes
Please support our sponsors and let them know you heard about them on AquariumAdvice.com
Old 10-05-2011, 07:42 AM   #1
Aquarium Advice Regular
Join Date: Nov 2006
Posts: 50
When to change RODI filters

This has to be our most frequently asked question, so our response might be useful to folks here:

A good rule of thumb is to replace your sediment filter and carbon block after six months. A more precise way to maximize the usable life of these two filters is to use a pressure gauge to identify when pressure reaching the membrane starts to decline. This is your indication one or both of the filters is beginning to clog.

Also be cognizant of the chlorine capacity of the carbon block. A good 0.5 micron carbon block for example will remove 99% of chlorine from 20,000 gallons of tap water presented at 1 gpm. Some original equipment suppliers commonly provide carbon cartridges rated at 2,000 to 6,000 gallons.

Regarding your RO membrane and DI resin, use your TDS meter to measure, record, and track the TDS (expressed in parts per million) in three places:
1. Tap water
2. After the RO but before the DI
3. After the DI.

The TDS in your tap water will likely range from about 50 ppm to upwards of 1000 parts per million (ppm). Common readings are 100 to 400 ppm. So for sake of discussion, let's say your tap water reads 400 ppm. That means that for every million parts of water, you have 400 parts of dissolved solids. How do we go about getting that TDS reading down to somewhere near zero?

If you do some experimenting with your TDS meter, you'll note that your sediment filter and carbon block filter (collectively called “prefilters”) do very little to remove dissolved solids. So with your tap water at 400 ppm, you can measure the water at the “in” port on your RO housing and you'll see it is still approximately 400 ppm.

The RO membrane is really the workhorse of the system. It removes most of the TDS, some membranes to a greater extent than others. For instance, 100 gpd Filmtec membranes have a rejection rate of 90% (i.e., they reject 90% of the dissolved solids in feed water). So the purified water coming from your 100 gpd membrane would be about 40 ppm (a 90% reduction). Filmtec 75 gpd (and below) membranes produce less purified water (aka “permeate”), but have a higher rejection rate (96 to 98%). The life span of a RO membrane is dependent upon how much water you run through it, and how dirty the water is. Membranes can function well for a year, two years, or more. To test the membrane, measure the total dissolved solids (TDS) in the water coming in to the membrane, and in the purified water (permeate) produced by the membrane. Compare that to the membrane’s advertised rejection rate, and to the same reading you recorded when the membrane was new. Membranes also commonly produce less water as their function declines.

After the RO membrane, water will flow to your DI housing. DI resin in good condition will reduce the 40 ppm water down to 0 or 1 ppm. When the DI output starts creeping up from 0 or 1 ppm, you know that your resin needs to be replaced. Sometimes people complain that their DI resin didn't last very long. Often the culprit is a malfunctioning RO membrane sending the DI resin “dirty” water. This will exhaust the resin quicker than would otherwise have been the case. Sometimes the problem is poor quality resin – remember that all resins are not created equal.

Buckeye is offline   Reply With Quote

change, filter, filters, rodi

Please support our sponsors and let them know you heard about them on AquariumAdvice.com

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
Ebay Ro/di replacement filters carey General Hardware/Equipment Discussion 11 11-27-2011 10:28 PM
When to change filters basket440 Saltwater Fish Only & FOWLR 3 09-01-2011 01:54 PM
neccessary to change filters? AmyD Freshwater & Brackish - Getting Started 4 09-01-2011 12:09 PM
PWC and Prime Mumma.of.two Freshwater & Brackish - General Discussion 75 08-12-2011 12:50 AM
Max pH Change at Water Change tlkng1 Freshwater & Brackish - General Discussion 14 06-25-2011 06:03 PM

» Photo Contest Winners

Our Communities

Our communities encompass many different hobbies and interests, but each one is built on friendly, intelligent membership.

» More about our Communities

Automotive Communities

Our Automotive communities encompass many different makes and models. From U.S. domestics to European Saloons.

» More about our Automotive Communities

Marine Communities

Our Marine websites focus on Cruising and Sailing Vessels, including forums and the largest cruising Wiki project on the web today.

» More about our Marine Communities

Copyright 2002-2012 Social Knowledge, LLC All Rights Reserved.

All times are GMT -4. The time now is 05:02 AM.

Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2016, vBulletin Solutions, Inc.