Search results

I have 5 120 running 50%

This is per channel, your channel 1 feed to Vin and Vout goes to the driver 1, repeat for channel 2 same circuit

Just read your first post, your controller output 0-10v and this led driver takes 0-5 or 5v PWM so you will need a voltage divider. Add 2 1K resistor.

Just hook up your driver to the black and yellow wire.

Pictures?

Haven't made any new post lately about my tank, you can check the beginning here. at http://www.aquariumadvice.com/forums/f71/my-125g-sw-tank-120049.html and http://www.aquariumadvice.com/forums/f71/update-on-my-125g-186783.html

Update, one year gone, all 5 fixture runs perfectly fine, some rust start to develop on some of the screw heads but the powder coated buddy rust free. Opened up one of them yesterday to clean the fans and check how is everything inside, so far looks great, no burn marks, melted parts or...

You need to find out if your drivers are dimmable, and even if dimmable is it PWM or analog, if analog 0-5 or 0-10 Its not that hard to disassemble the driver, look at pcb for marking, take picture and upload it if you cannot determine it yourself. Measure the voltage on the center pin of your...

I have 2, still working ....

Yes uv would be 10-400nm as per wiki, 430nm led probably will have better effect on my corals than green. Sent from my iPhone using Tapatalk

5 would not fit otherwise :) Sent from my iPhone using Tapatalk

Definitely nutrient problem since it was a problem even with T5. Also I have changed in 3 module the 4700k LEDs with 14000k and the greens with 430nm uv what I got for my diy kit. Sent from my iPhone using Tapatalk

http://bit.ly/15FMiRY Looks like the store closed for the Chinese New Year . They claim that they are the manufacturers of this light so you got it straight from the factory, no middle man. I purchased 4 extra drivers from them in separate order to finish my diy led fixture what I started over...

I have 5 of this module from eBay store. Friend of my got 3 from a different store. I have open them up to add PWM dimming, here is some of the major difference. My drivers run 100% at 108v 750mA = 81W per channel 162W total his runs at 105v 530mA = 56W 112W. My drivers have PWM input but not...

http://www.ebay.com/bhp/3w-led-lens You will need to take apart the whole unit, all connection are plugins so shouldn't be that hard.

I short of real estate in my tank, anyone want to trade or give me ~$50 for each of my red rose bubble tip anemone's ? I'm interested to trade for anything so dont be shy :) I'm in Edmonton Bellerive area. http://goo.gl/maps/EUIh2

RRBT for sale/trade I short of real estate in my tank, anyone want to trade or give me ~$50 for each of my red rose bubble tip anemone's ? I'm interested to trade for anything so dont be shy :) I'm in Edmonton Bellerive T5Z 2P9 area. http://goo.gl/maps/EUIh2

125G Display, 33G sump.

Green Star Polyps

Great pictures guys. After numerous crash my tank finally recovering again.

If you just going to trow it out, I will take it from you for $20+ shipping to Canada Hope you get your warranty tho.

This is why I'm leaning towards cheap Chinese pumps, if they beak and they will break just like the major big brands its only cost fraction of the major big brand even if you replace it every year. My main pump is a Jebo4500 $139, you could buy probably a tiny fountain circulation pump if is...

50st and 127ave east corner.

Hi everyone. I'm in Edmonton, currently have 120G sw display and 33G sump. Aquarium illusion is my favorite place but often go to AquaGiant. Both of this store sometimes out of reality with prices but at AG at least I can bargain with the owner. Other than salt and a few frag I buy everything...

I only go there to look around, expensive and don't like the idea of buy what we sale, good luck trying to get what you want. Buy a pump for $100 than buy replacement impeller for $47