Search results

So a good cleaning of the mixing can should be done after each use? Rich

I run a 5 stage RO/DI...when I take a TDS reading in my holding can its 000ppm. Then I move the water to my mixing can and just by dumping it in there TDS jumped to 082ppm. Now i've mixed water in there before and there was some salt residue on the sides of the can when I dumped the fresh water...

Thanks, I was told about changing the photo period...then told not to. I knew I would get it answered here. Thanks, Rich

I will be switching 2 of my 3 175's to 400's. What kind of acclimation do I need to go through...or do I? Current setup is 3 175's over a 120gal mixed reef...I will be replacing my outer 175's with the 400's. I'm gonna keep my SPS to the outsides and softies in the center. Thanks, Rich

Actually the skimmer was adjusted high but i've been using it like that since I bought it back in March. I've since lowered it but will lower it even more til I get dark skimmate again. Its a CPR... it came with my CPR Aquafuge Pro. Its powered by a tiny Rio 600. Thanks, Rich

Lately my skimmer has been skimming twice as fast as usual, the cup fills twice a day now. The skimmate is now mostly clear with a little tan color, and does not smell that bad. What would cause this? Does this usually happen from time to time? Or is my water just that clean 8O LOL Thanks, Rich

Yes, you dont want to use it right after its mixed. You want to wait at least a few hours for it to settle, I typically let it sit over night. Leaving it three days should be ok, but I hear it looses its potentcy after 5 days. Rich

If you have a protein skimmer that will help pull alot of crud out. Try doing 20-30% water changes and vacuuming your LR and substrate. I wouldnt add any chems to your water. JMO Thanks, Rich

I also was having problems getting my Ca. up. Then Mg. was brought to my attention so I dosed with ESV Mg. it helped but was still under the 1300ppm mark. So I used Kent Tech M which was very weak :x , then I seen something about using epsom salt. Worked like a charm and for only $.99 a box...

Cool, I am gonna go for the GAC. I think i'll put it where the refuge water pours into the sump, thanks for your help Biggen. Thanks, Rich

Wher would I put the carbon and what would I put it in? I use an Aquafuge pro from CPR its split into 3 chambers, intake side with the skimmer, middle is the refuge, and the third is the sump(very small if you ask me) which my mag 18 sits in and takes up alot of room. As for the micron bag would...

Was wondering what would be the best way to further polish my water? Currently my setup includes: 120gal 130lbs LR 100-120lbs LS protien skimmer fuge with LS and chaeto algae Does anyone use sand filters anymore? My LFS owner swears by them and says you get awesome water clarity. Thanks, Rich

What is the best source for softies and LPS on the internet? Thanks, Rich

For kalk? Rich

Gotcha, so it would be in the coral and my best interest to slowly lower my Ca. down to 380-400ppm? I am doing a water change tomorrow or Tuesday, what would you recommend my Ca. level in my change water be? If my tank water is at 480ppm right now. Also what is the formula to get the balanced...

Somewhat, for instance...I run my tank at a SG of 1.024 and Ca. is between 450-480ppm. Am I in the safety zone? So what i'm doing is speeding up the corals growth but actually at the same time giving it a somewhat toxic environment?? Thanks, Rich

If thats the case why does everybody recommend such a higher Ca. level than what you say? Also some sea salts measure Ca. levels of 400ppm right out of the bag...is that too high?? I'm a bit confused on that one because when I had a Ca. level of 350ppm I was being told to raise it or my corals...

I've got the past three issues of Coral magazine and like it alot. Every issue usually covers one big topic and then a few smaller articles, like my first one covers nano reefs, the second seahorses, and the third is about giant clams. The articles are very in depth and informative, yes...

My plan was to draw water from over the top with a pvc pipe running down the back(inside) of my tank and drill it full of holes to draw the water in. If I painted the pvc pipe with the purple primer would it have to sit and cure before I put it in the tank? What size/brand pump should I use? I...

When I setup my 120gal I didnt drill for a CL, currently I use a couple of Rio ph's for circulation. I want to get as many of the ph's out of the tank as I can. I know I cant drill the back of the tank now but I seen something in another forum where they drilled the tops of the acrylic aquarium...

I've had that xenia for about a month now, I moved it the other day during some maintenance. I've moved it before and never seen it do that before. No signs of any goo but I did see a tip floating around today but couldnt tell if it was from that xenia or my other one. No nudi's that I am...

In the first pic the two stalks on the left and right sides are withering away now. Ph has been hovering around 8.3-8.4 within the last week. Thanks, Rich

Lets try these. Rich

Thats interesting cause about 3 months back my LFS had a customer appreciation day and I bought 2 bangaii's. When I got them home and acclimated they immediately hid behind my LR. by the third day both were dead :( The LFS was moving fish very fast that day you had to get a number, so I think...

I feed mine a piece of krill every week or so when I remember, but like reefrunner said you dont need to directly feed them. So far i've never got stung and if I did...i never felt it :D Rich